How to Change a Subaru Spare Key

If you lose your subaru key fobs car key, call a locksmith. Usually, they can cut an alternative key for you cheaper than the dealer.

Subaru car keys are typically either intelligent "push-to-start" fob remote keys, or simply keys made of metal. The Fob key has a chip inside and it will require reprogramming.

Keyless Entry System

The key fob can be used to lock and unlock your Subaru remotely. It also opens the trunk of your car or the lift gate. These remotes use the keypad inside your car to communicate with your vehicle's computer.

Certain models of Subaru have a feature that is not widely known called PIN Code Access. It allows you to use a personalised sequence of numbers to open and start your vehicle. If you own a more recent Subaru Forester, Outback, Crosstrek, WRX, WRX STI or Impreza that has this feature, check your owner's manual to see how to make use of it.

If your keys stop working, there's a good chance that the battery in the key fob is dying. You can test the battery life of your key fob with an instrument that is portable or a multimeter in your garage.

The next step is to take the circuit board for the transmitter from the key fob, and then look at it. It will have one or two sets of eight-digit numbers, so write down the first set so that you can remember it later. After you've done this you can start programming the key fob at home. This procedure is different based on the model and year your car. However, it is usually easy enough to do yourself.

Key Fobs

subaru remote key's most recent models all come with key fobs that can not only unlock your doors and activate your lights, lock your gas cap, and even start your vehicle. This last feature is particularly useful if you've ever parked at the gas station only to find that your car isn't starting because the key fob battery has died.

If your Subaru is brand new or old it's likely that the key fob can be replaced with little difficulty. Be aware that some of the modern models, with their advanced technology, may require an appointment with a dealer. But, with a bit of time and effort, you can get your new key fob to use at home.

Begin by opening the case and inspecting the circuit board of the transmitter. (Instructions on how to open the case are usually provided in the owner's manual). It should have two or three sets of serial numbers, each one of which is 8 digits long. Note down the first number in the series and keep it in your wallet to refer to later on.

Then, get into the driver's chair and close all of the doors. Turn the key 10 times to start your car, then turn it off. Press the lock button of your key fob, and then open the door. This will verify whether your doors are operating properly. Close the door, then take the key off. The chime should be heard from your vehicle once more to indicate that the key fob has been programmed.

Ignition System

The battery for the key could be dead If your Subaru keys aren't functioning as they should. If you have the knowledge, you can replace the battery of your key fob yourself. A replacement battery is not expensive and easy to locate. If your key fob doesn't respond to your commands, it could be a different issue. To find a spare key, it's advisable to go to an authorized dealer. They can ensure that the key is an original Subaru key, under warranty, and is programmed to your vehicle. This is a lot simpler and safer than buying an aftermarket key from a retailer online.

The dealer will also cut keys for you, provided you provide them with your VIN number as well as evidence of ownership. The information provided will be used to identify the key replacement so that it can be accepted by your immobilizer. This is a more intricate procedure than cutting a key, and the dealer will charge more for it.

Once the new key has been programmed, you can replace it with your working key. It will take only five seconds to insert the second key, which is why it's vital to have an operational key in your pocket. You can take the key off after the security light has stopped flashing, and then test it.

Battery Replacement

One of the primary features that makes Subaru fobs useful is their ability to turn on your car key cutting and programming near me's power windows and sunroof with a single touch of a button. The battery inside your subaru outback key fob isn't built to last forever, and it will require replacement at some point. This quick guide from Capitol Subaru will help you to change the battery yourself.

To begin the process, you'll have to find the tiny crevice inside the seam that separates the back and front of your key fob. You can then open the seam with an flat-head screwdriver to expose the small compartment that contains the battery. Remove the old battery and then install a new one, making sure it is facing the correct side upwards. After everything is in place then you can use the new key fob to lock or unlock your vehicle with ease!

You should always have a spare set keys, especially if yours is damaged or has gone missing. You can purchase a brand new key from your local dealership or get it cut by a locksmith. It is essential that your key fob is working properly as soon you can so that you can safely drive.