How to Repair Car Keys

car key repair company keys may seem tiny and insignificant, but they are essential to the functioning of your vehicle. Replacing an old key or a transponder one could cost as much as $200.

There are solutions to fix your car keys yourself for a fraction of the price. This article will discuss the most frequently encountered car keys issues as well as the DIY solutions to fix them.

Dead Key Fob Battery

Cars are equipped with remote car key repair near me key fobs that allows opening the doors, trunk and tailgate more convenient than ever before. The battery of this device is susceptible to dying. There are a few strategies you can employ to fix this issue fast.

First, determine if the car is in ignition mode. If it is, the battery of the key fob may be drained instead of dead. To test this, press the button on the key fob right towards the ignition button. If it works, then the battery is probably fine and only requires to be replaced.

To replace the fob's battery, begin by prying open the case with a screwdriver or watch-type tool. Be careful not to apply too much force as this could cause the fob's casing to split. If the fob isn't opening open easily, try wedge your pry tool in several places around the outside of the case.

Open the electronic compartment of your car once you have removed the mechanical key. Then, insert the battery replacement and then snap the shell together. If your key fob still isn't working after this, it could be that there is an problem with the remote start system of your vehicle. This will require an expert to identify. A reputable mechanic will in a position to assist you in this situation. You can also reach out to roadside assistance to assist with your vehicle in case you need it.

Broken Key Ring

If your key fob won't work because the ring broke there are a few options you might try. First, you should check to see if your broken piece is still inside the ignition key repair near me. If it's still in there, remove it without damaging the ignition lock or the door lock. Call a locksmith if you are having difficulty taking the key off. They have tools that can safely remove keys that are damaged from the ignition.

Another common cause of the car key breaking is the corrosion of the circuit board or plastic frame. You can clean the board with cotton swab. This will eliminate the corrosion and prevent damage to the contact pads.

You can repair a damaged rings by using a thick nail or wire to close the hole. Superglue can be used to fix damaged key rings. First, clean the damaged rings with a damp cloth and then apply a small amount superglue to each end of the wire or nail. Press the pieces together and let them dry before using your car. These DIY solutions can appear appealing, but they're just a stopgap measure. For long-term repairs, it's best to work with an experienced locksmith. They have the expertise and tools to fix the broken key quickly and efficiently. They can even replace the battery in the key fob and change it's programming if required.

Broken Key Blade

Some key blades might break due to wear and tear. If this happens, it's probably time to get a new key. The issue isn't as serious as you might believe at first. The issue is that the metal blade has broken off from the case.

Spraying lubricant into the keyhole is one way to fix it. You can then use pliers or tweezers to grasp the damaged end of the key and pull it. You can also make use of a magnet if the key is magnetic. Use a magnet to assist you remove the key, but be cautious to not sever the lock tumbler.

Contact a locksmith right away when you are unable remove the broken piece of the key. They're equipped with special tools that can safely remove keys without causing damage.

You can also try super glue to repair a snapped key. Apply a small amount of glue to the edges of the crack and press them together. Make sure the glue is dry before inserting the key into the lock. This method isn't reliable and you may have to repeat the process multiple times before it works. Additionally, the super glue may not be enough strong to hold the key together. This is more of a temporary fix than a permanent solution.

Broken Plastic Loop

If the plastic loop on your key repair car fob is damaged it could render the key ineffective. This is a simple fix. As a replacement alternative, you can opt for a thick wire or finishing nail. For each end of the wire or nail you need to drill two holes into the plastic loop. Cut the nail or wire to key width and put a drop of superglue on each hole. Press the nail or wire into the holes and allow them to dry.

A locksmith who sells replacement shells is a different option. They can remove the programmable part of your key, move it to the new shell, and cut an entirely new blade for less than a complete replacement cost.

It's not the most ideal solution, but it'll help you get back on the road if your key split in half. However, it can be difficult to fix the blade of the key if it's in the ignition. If you're not cautious you could use a hair clip or a needle to remove the damaged part from the ignition. The best solution is to contact a locksmith with special tools for safely removing broken keys from the ignition. They can also create new keys that have the appropriate cuts for your vehicle's ignition and ensure it works correctly when inserted into the lock.

Broken Master Key

You'll need to try to retrieve the key before it's completely destroyed. There are a variety of methods that you can try, such as using lubricants and tools like needle nose pliers and tweezers. These tools can take a small piece of the broken key and remove it.

Spray the inside of your lock with WD-40 or a graphite powder. You can also employ the hacksaw blade method by moving the blade along the sides of the broken key, and grabbing onto some of its 'teeth.' If you are successful then you should be able to take the broken key out.

Many hardware stores carry the spiral key extraction tool. It is a thin flexible rod with spiral threads that can be inserted into the keyway, and then bent into the broken part of the key. Once it has hooked onto the serrations, it is possible to twist it in a circular motion and lever it against the broken portion of the key repair to take it out.

It's worth trying to remove a master key that's broken prior to calling a professional locksmith. If you can't get an item out, you need to call in the big guns and get a locksmith to make you a brand new key and reprogram it to the transponder in your car.